All rights reserved - SPM Thermo-Shield © Site by  Cybernetic Web Design

Home About Us Products Find a Distributor Info / Testing Photo / Video Contact Alert !
Protected by Copyscape Web Plagiarism Checker

THERMO-SHIELD ®   INTERIOR WALL

INTERIOR WALL COATS

DESCRIPTION
Thermo-Shield® Interior Wall Coats are highly efficient, energy-saving, flexible coatings, designed to insulate and waterproof your walls. They are non-toxic, friendly to the environment, and form a monolithic (seamless) membrane that bridges hairline cracks.
They are completely washable and resist many harsh chemicals and dirt pick-up. These water-based coatings are made from an acrylic resin system filled with vacuumed ceramic micro spheres that acts as a thermally efficient blanket. Thermo-Shield® Interior Wall Coats can be applied by roller or sprayer. Thermo-Shield® Interior Wall Coats have 4 times the fire resistance and 1/26th the smoke development necessary to classify for Class I rating. They have superb adhesion, chemical resistance and reduce sound transmission and echo. They help maintain a more uniform temperature ceiling-to-floor and reduce cold weather heat loss through walls and ceilings. These coatings come in a variety of architectural colors and leave a beautiful matt finish.
















INSULATION
Reflectivity 89%, Emittance 94%, Conductance 0.06 W/mK

TYPICAL USES
For regular indoor painting where durability, reduction of the noise factor and superb smoke protection are important. Thermo-Shield® Interior Wall Coats reduce condensation and help maintain an even level of comfort in the room.

STANDARD INTERIOR: Used in most climatic conditions. It has superb fire resistance, chemical resistance and is non-toxic, safe and washable.

TROPICAL INTERIOR: With the same properties as STANDARD, it is used in climatic conditions where fungi growth is a major concern.

PRIMER
No primer is usually required but it is recommended over gypsum board. Follow instructions for proper application and film build-up.

SURFACE PREPARATION
All surfaces must be clean and free from laitance (efflorescence), dust, dirt, rust, oil and grease. Minimally, surfaces must be cleaned to remove any loose or chipping paint, or any other foreign material prior to coating.

COLORS
White and any custom color available. Darker colors will give a correspondingly lower reflectivity.

THEORETICAL COVERAGE (2 Coats)
10.4 m² per gallon at 150 microns DFT (112 sf/gallon at 6 Mills DFT)

SHELF LIFE
Minimum 2 years (keep from freezing)

DRYING TIME
To set: 20 minutes / Too re-coat: 4 hours / To through: 12 hours
At 24 Deg C (75 Deg F) and 50% relative humidity

THINNING
None required. Clean water in small amounts of up to 0.24 Liter per gallon (1 cup) may be added to replace evaporation losses or to adjust for spray equipment configuration.
Caution: excessive thinning will cause the coating to lose adhesion and elasticity.

EQUIPMENT
Roller or airless spray application is recommended. Very small areas may be brushed.
When Thermo-Shield® Interior Wall Coat is applied by brush, three (3) coats cross-brushed is required for adequate protection.
Airless Sprayer:
Tip Orifice: .031 inches
Atomizing Pressure: 2200 - 2500 psi
Fan Spread: 60 Degrees
Pump: Minimum 1 gallon per minute at 2500 psi
Filter: Remove filters and screens
Prime pump with water before attempting to spray Thermo-Shield® Interior Wall Coat.
Acceptable equipment includes: Binks Super Hornet, Graco 433 or larger, and many others.

METHODS
To assure adequate and uniform coverage, the “spray and back roll” techniques are recommended. Do not cross spray - each coat should be sprayed in the same direction to avoid showing undulations and other imperfections in the walls. Thermo-Shield® Interior Wall Coats should be applied in full wet coats.

CLEAN UP
Clean tools and equipment with warm soapy water. Rinse with clean water; flush mineral spirits through spray equipment to prevent rusting and to lubricate packing and gaskets.

PACKAGING
1 gallon cans, 5 gallon pails and Lined 55 gallon drums.

APPROXIMATE SHIPPING WEIGHT
Net weight per gallon: 4.5 kg (10 lbs)
Case of 4, 1 gallon cans: 19.96 kg (44 lbs)
5 gallon pails: 22.7 kg (50 lbs)
55 gallon drums: 272 kg (600 lbs)

V.O.C.
39.5 grams / liter (0.33 lbs / gallon)

STORAGE
Store at minimum 1 Deg C (33.8 Deg F) - maximum 30 Deg C (86 Deg F)
DO NOT FREEZE

SETA FLASH POINT DOT CLASS
Non-flammable Not regulated

PRODUCT CODES
INTERIOR WHITE: 5977 / INTERIOR ACCENT BASE: 5963 / INTERIOR TROPICAL: 5976

PRODUCT WARRANTY
10 years

EXCLUSIVE REMEDY
The sole remedy for goods not in conformance with any warranty is replacement of the product. SPM Thermo-Shield® Inc. shall not be liable for any other damages, including, but not limited to labor expenses.



Top of Page
#

INTERIOR WALL APPLICATIONS

Roof Coat Applications
Green Products