INTERIOR WALL COATS 5

 

DESCRIPTION

Thermo-Shield® Interior Wall Coats are highly efficient, energy-saving, flexible coatings designed to insulate and waterproof your walls. They are non-toxic, friendly to the environment, and form a monolithic (seamless) membrane that bridges hairline cracks. They are completely washable and resist many harsh chemicals and dirt pick-up.  These water-based coatings are made from an acrylic resin system filled with vacuumed ceramic micro spheres that acts as a thermally efficient blanket. Thermo-Shield® Interior Wall Coats can be applied by roller or sprayer.  Thermo-Shield Interior® Wall Coats have 4 times the fire resistance and 1/26th the smoke development necessary to classify for Class I rating.  They have superb adhesion; chemical resistance and reduces sound transmission and echo.  They help maintain a more uniform temperature ceiling –to-floor and reduces cold weather heat loss though walls and ceilings.  These coatings come in a variety of architectural colors and leave a beautiful satin finish.

 

INSULATION

Reflectivity 89% - Emittance 94% - Conductance 0.06 W/mK – Endothermic Effect®

 

TYPICAL USES

For regular indoors painting where durability, reduction of the noise factor and superb smoke protection are important.  Thermo-Shield® Interior Wall Coats reduce condensation and help maintain an even level of comfort in the room.

 

PRIMER

No primer is usually required but it is recommended over gypsum board.  Follow instructions for proper application and film build-up

 

SURFACE PREPARATION

All surfaces must be clean and free from laitance, dust, dirt, rust, oil and grease.  Minimally, surfaces must be cleaned to remove any loose or chipping paint, or any other foreign material prior to coating.

 

COLOR

Tinting may be achieved with Thermo-Shield® Interior Wall Coatings by the addition of universal colorants.  Darker colors will give a correspondingly lower reflectivity.

 

PERCENT NON-VOLATILE:      

46.61% by VOLUME / 49.77% By weight

 

THEORETICAL COVERAGE

 (To be applied in 2 coats)

10.4 sm.  Per gallon at 150 microns DFT with no loss. (130 sf/gl at 6-mills DFT)

 

DRYING TIME

To set:  20 minutes

To re-coat:           4 hours

To through:        12 hours

(At 24 deg C and 50% relative humidity)

 

THINNING

None required.  Clean water in small amounts (up to 0.24 Liter –1 cup- per gallon) may be added to replace evaporation losses or to adjust for spray equipment configuration.  Caution: excessive thinning will cause the coating to loose adhesion and elasticity.


 

EQUIPMENT

Roller or airless spray application is recommended.  Very small areas may be brushed.  When Thermo-Shield® Interior Wall Coatings are applied by brush, three (3) coats cross-brushed are required for adequate protection.

 

AIRLESS SPRAY:

Tip Orifice                                  .031 inches

Atomizing Pressure        2200 - 2500 psi

Fan Spread                               60 Degrees

Pump                                        Minimum 1 gallon per minute at 2500 psi

Filter                                         Remove filters & screens

*** Prime pump with water before attempting to spray Thermo-Shield® Wall Coatings.  Acceptable equipment includes Binks Super Hornet, Graco 433 or larger, and many others.

 

METHODS

To assure adequate and uniform coverage, the “spray and back roll” techniques are recommended – spray all coats in the same direction, do not cross spray to avoid showing undulations and other small imperfections in the walls.  Thermo-Shield® Interior Wall Coats should be applied in full wet coats.

 

CLEAN UP

Clean the tools and equipment with warm soapy water.  Rinse with clean water; flush mineral spirits through spray equipment to prevent rusting and to lubricate packing and gaskets.

 

PACKAGING

One and five-gallon pails. 

 

APPROXIMATE SHIPPING WEIGHT

Net weight per gallon                  4.55 kg (10 lbs)

Case of 4 1-gallon cans              19.96 kg (44 lbs)

Five-gallon pail                           23.63 kg (52 lbs)

 

STORAGE

Minimum 0 Deg. C                     Maximum 30 Deg. C  DO NOT FREEZE

 

SHELF LIFE

Minimum 2 years (keep from freezing)

 

SETA FLASH POINT                                         DOT CLASS

Non-Flammable (water based)                             not regulated

 

PRODUCT CODES

INTERIO WHITE: 5977 INTERIOR/EXTERIOR ACCENT BASE: 5964

 

WARRANTY:  10 year LIMITED WARRANRY

 

 german_intgerman_int01german_int02german_int03german_int04        

 

 

www.thermoshield.com

spm@thermoshield.com                                                                                    
                                                                                                                             logo_home

 
P.O. Box 631, Custer, South Dakota 57730 USA   
Ph: 605-673-3201/Fax: 605-673-3200  
www.thermoshield.com   spm@thermoshield.com
  Site Map